Showing 1–12 of 32 results
The Ag59800-ULP is an ultra-low profile (11mm), IEEE802.3-compliant (af/at/bt) PoE++ PD module engineered for space-constrained applications. Operating as a Type 4, Class 8 device, it utilizes a highly efficient (up to 95%) DC/DC converter to extract power from standard Cat5 cabling, delivering low-noise 12V or 24V outputs alongside essential hardware safeguards including thermal protection, short-circuit defense, and a 1500Vdc isolation barrier.
Read more
- Ultra-Low 11 mm profile, with a compact 70 mm × 35 mm package size
- Flexible mounting options - SMT and TH
- 95% efficient 100W DC/DC converter
- IEEE802.3bt class 8 PD (PoE++) for up to 89W output applications
- 12V and 24V Output variants available
Ag59800-LPB series Power-over-Ethernet (PoE++) modules are designed to extract power from a conventional twisted pair Category 5 Ethernet cable, conforming to the IEEE802.3 PoE standard, with full compatibility with the IEEE802.3bt, IEEE802.3at and IEEE802.3af amendments.
The Ag59800-LPB is pre-configured as a Type 4 Class 8 device, requesting a minimum of 90W of power from the PSE, with nominal output voltages of 12V or 24V.
The high efficiency DC/DC converter can achieve up to 95% efficiency and operates over a wide input voltage range with a low ripple and low noise output. The DC/DC converter also has built-in output overload, output short-circuit and over-temperature protection and provides a 1500Vdc (input to output) isolation barrier, as required by the IEEE802.3 specification.
Read more
- 95% efficient 100W DC/DC converter
- IEEE802.3bt class 8 PD (PoE++) for up to 89W output applications
- 12V and 24V variants available
- Low output ripple & noise
- Overload, short-circuit and thermal protection
The Ag59600-LPB series Power-over-Ethernet (PoE++) modules are designed to extract power from a conventional twisted pair Category 5 Ethernet cable, conforming to the IEEE802.3 PoE standard, with full compatibility with the IEEE802.3bt, IEEE802.3at and IEEE802.3af amendments.
The Ag59600-LPB is pre-configured as a Type 3 Class 6 device, requesting 60W of power from the PSE, with nominal output voltages of 12V or 24V. The high efficiency DC/DC converter can achieve greater than 94% efficiency and
operates over a wide input voltage range with a low ripple and low noise output. The DC/DC converter also has built-in output overload, output short-circuit and overtemperature protection and provides a 1500Vdc (input to output) isolation barrier.
Read more
- Up to 60W peak and 51W continuous output power (IEEE802.3bt class 6)
- 94% efficient DC/DC converter
- 12V and 24V variants available
- Excellent Thermal Management
- Overload, short-circuit and thermal protection
The Ag5810 is an IEEE802.3bt Type 4 Power over Ethernet module that can deliver up to 60 Watts of output power. Suitable for applications such as WiMAX access points, PTZ cameras, notebook computers, IP cameras, LED lighting, intelligent displays and thin client terminals.
The Ag5810 extracts power from an IEEE802.3bt Power Sourcing Equipment (PSE) over an Ethernet cable, conforming to the IEEE802.3bt standard for signature recognition with class programming-fixed to class 7. It has been designed to work with IEEE802.3bt PSE’s and existing high power PSE’s from leading manufacturers.
The high efficiency DC/DC converter operates over a wide input voltage range and provides a regulated low ripple and low noise output. The DC/DC converter also has built-in overload, thermal and short-circuit output protection.
Read more
- Smallest 60W ‘bt’ solution in the world
- DIL - 70mm(L) x 30mm(W) x 16mm(H)
- Power received on all 4 pairs - Type 4, Class 7
- Overload, thermal & short-circuit protection
- Very low power standby mode
Ag102 is Silvertel’s first battery charger module. Designed to maximise battery lifetimes while reducing power consumption using intelligent charging techniques and our high efficiency DC-DC converter, Ag102 is very eco-friendly technology.
Read more
- Maximises Battery Life
- Battery Reversal Protection
- Reduces Power Consumption
- Intelligent ‘Top-up’ Float Charge
- Programmable Charge Current
Ag103 is a charge control module, designed to maximise battery life and reduce life cycle maintenance and call out costs. Ag103 uses Maximum Power Point Tracking (MPPT) techniques with intelligent charging profiles and a high efficiency DC-DC converter to optimise the available solar power for charging. This module has been specifically designed for for use with Solar Panels as the power source and for charging 12V Solar Batteries. These solar batteries are designed for maximum lifetime with a very high number of deep discharge cycles.
Read more
- Designed for use with Solar Panels
- Max Power Point Tracking (MPPT)
- Maximises Battery Life
- Wide input supply range 9V - 36V
- Selectable Charge Profiles for 1.2Ah to 12Ah
The Ag105 is a solar charge controller for protected Lithium-ion (Li-ion) and Lithium Polymer (Li-Po) batteries that can also be used with a fixed DC supply in standalone applications. The module requires very few supporting components to configure the charge controller to any application.
With a wide operating input range of 11VDC to 36VDC and using intelligent charging techniques, such as Maximum Power Point Tracking (MPPT), the Ag105 will adjust the charge rate to optimise the power produced by a solar panel.
The Ag105 can be configured for 1, 2 or 3 series cell Li-ion batteries, with 4 voltage per-cell options to balance serviceable battery lifetime and usable capacity.
Read more
- Solar panel or fixed DC source charge controller for Lithium-ion battery packs
- Maximum Power Point Tracking (MPPT)
- JEITA compliant Lithium-ion battery charger
- Wide input supply range 11V - 36V
- Adjustable charge voltage and current
Ag1171 is a low cost single channel SLIC with a fully integrated DC-DC converter to generate all necessary battery and ringing voltages. The module only requires a single supply from +3.3V to +5V. Ag1171 is suitable for low line count, short loop applications, such as Wireless Local Loop Terminals (WLL), Fixed Cellular Terminals (FCT), Fixed Wireless Terminals (FWT) and Internet Telephony (VoIP).
Read more
- Low Cost
- Very Simple integration
- Small size - SIL package
- 600R impedance
- On-board ringing generator
The world’s first +3.3V only ringing SLIC. Also available as a +5V version, Ag1170 has a built in DC-DC converter to generate all of the required telecom and ringing voltages on board – all from a single +3.3V (or +5V) supply. Ag1170 is available in Single-in-Line (SIL) or Dual-in-Line (DIL) footprints, ideal for VoiP applications.
Read more
- 600R and Programmable impedance options
- Very small SIL and DIL package options
- Very Simple integration
- On-board ringing generator
- Integral high efficiency DC/DC converter, providing:
Ag1110 is a low cost, long loop SLIC, in a space-saving Single-in-Line (SIL) package, requiring very few external components. Suitable for use in high line count applications such as Central Office, PBX, Digital Loop Carrier and Pair Gain Systems.
Read more
- Very simple integration
- Constant current feed to the line, with
- constant voltage fold over
- Single +5V system side power supply
- 600R impedance
The Silver Telecom ST003 is a highly integrated, 21-pin DIL Subscriber Line Interface Circuit (SLIC) engineered for space-constrained and harsh environments (-55°C to +85°C). Compliant with G712 standards for loop lengths up to 3.0km, it minimizes external component requirements by incorporating an onboard DC/DC converter and ringing generator to operate from a single power supply. Its direct codec compatibility and robust thermal tolerance make it an ideal, cost-effective solution for industrial, military, and low-line-count telecommunications applications, including VoIP, WLL, and SOHO networks.
- Wide temperature range -55C to +85C
- 600R impedance
- Very small DIL package
- Very Simple integration
- On-board ringing generator
Silvertel’s Ag210 PoE constant-current LED driver module is designed to combine high power LED lighting applications with PoE connectivity. Conforming to the latest IEEE802.3bt Power-over-Ethernet (PoE) standard the module provides an easily implemented solution for designers/integrators of LED lighting systems.
Read more
- IEEE802.3bt compliant
- Type 3 Class 6 PoE PD
- Compact DIL package - 51mm(L) x 30mm(W)
- Overload, thermal & short-circuit protection
- Input voltage range (44-57V)
Visit Ecommerce Distributors
Recently viewed
The world’s first +3.3V only ringing SLIC. Also available as a +5V version, Ag1170 has a built in DC-DC converter to generate all of the required telecom and ringing voltages on board – all from a single +3.3V (or +5V) supply. Ag1170 is available in Single-in-Line (SIL) or Dual-in-Line (DIL) footprints, ideal for VoiP applications.
Read more
- 600R and Programmable impedance options
- Very small SIL and DIL package options
- Very Simple integration
- On-board ringing generator
- Integral high efficiency DC/DC converter, providing:
