Showing 1–12 of 31 results
Ag102 is Silvertel’s first battery charger module. Designed to maximise battery lifetimes while reducing power consumption using intelligent charging techniques and our high efficiency DC-DC converter, Ag102 is very eco-friendly technology.
Read more
- Maximises Battery Life
- Battery Reversal Protection
- Reduces Power Consumption
- Intelligent ‘Top-up’ Float Charge
- Programmable Charge Current
Ag103 is a charge control module, designed to maximise battery life and reduce life cycle maintenance and call out costs. Ag103 uses Maximum Power Point Tracking (MPPT) techniques with intelligent charging profiles and a high efficiency DC-DC converter to optimise the available solar power for charging. This module has been specifically designed for for use with Solar Panels as the power source and for charging 12V Solar Batteries. These solar batteries are designed for maximum lifetime with a very high number of deep discharge cycles.
Read more
- Designed for use with Solar Panels
- Max Power Point Tracking (MPPT)
- Maximises Battery Life
- Wide input supply range 9V - 36V
- Selectable Charge Profiles for 1.2Ah to 12Ah
The Ag105 is a solar charge controller for protected Lithium-ion (Li-ion) and Lithium Polymer (Li-Po) batteries that can also be used with a fixed DC supply in standalone applications. The module requires very few supporting components to configure the charge controller to any application.
With a wide operating input range of 11VDC to 36VDC and using intelligent charging techniques, such as Maximum Power Point Tracking (MPPT), the Ag105 will adjust the charge rate to optimise the power produced by a solar panel.
The Ag105 can be configured for 1, 2 or 3 series cell Li-ion batteries, with 4 voltage per-cell options to balance serviceable battery lifetime and usable capacity.
Read more
- Solar panel or fixed DC source charge controller for Lithium-ion battery packs
- Maximum Power Point Tracking (MPPT)
- JEITA compliant Lithium-ion battery charger
- Wide input supply range 11V - 36V
- Adjustable charge voltage and current
Ag1110 is a low cost, long loop SLIC, in a space-saving Single-in-Line (SIL) package, requiring very few external components. Suitable for use in high line count applications such as Central Office, PBX, Digital Loop Carrier and Pair Gain Systems.
Read more
- Very simple integration
- Constant current feed to the line, with
- constant voltage fold over
- Single +5V system side power supply
- 600R impedance
- 600R and Programmable impedance options
- Very small SIL and DIL package options
- Very Simple integration
- On-board ringing generator
- Integral high efficiency DC/DC converter, providing:
- Low Cost
- Very Simple integration
- Small size - SIL package
- 600R impedance
- On-board ringing generator
- IEEE802.3bt compliant
- Type 3 Class 6 PoE PD
- Compact DIL package - 51mm(L) x 30mm(W)
- Overload, thermal & short-circuit protection
- Input voltage range (44-57V)
Ag2120 is a highly integrated trunk or PSTN/COIC interface, available in either a Dual-in-Line (DIL) or Single-in-Line (SIL) package. The module boasts many integrated features, including a basic barrier on-chip and programmable DC mask. The Ag2120 can be used in systems without a ground, or in applications where common mode interference is very high. It can also be operated from either a +3.3V or a +5V supply.
Read more
- Highly featured PSTN interface
- Very small SIL and DIL package options
- Includes Transformer isolation
- On board Loop switch and Diode bridge
- Ringing and loop current detection
Ag2130 is a low cost single channel PSTN Interface in a Single-in-Line (SIL) package. The module provides many integrated features, including a basic barrier on-chip. It can be used in systems without a ground, or in applications where common mode interference is very high. Ag2130 can also be operated from either +3.3V or a +5V supply.
Read more
- Highly featured PSTN interface
- Very small SIL package options
- Includes Transformer isolation
- On board Loop switch and Diode bridge
- Ringing detection
The Ag5300 series are low cost PoE+ modules, in a Single-In-Line (SIL) package, that can deliver up to 30 Watts of output power. Options for 12V DC (Ag5300) or 24V DC output (Ag5324) are available. The module signature complies with both the IEEE802.3af and IEEE802.3at specifications and they are designed to meet the safety isolation requirements of IEEE802.3at. The exceptionally small footprint and package size make them ideal for space restricted applications such as IP Video Telephones, WiMAX access points, PTZ cameras and remote computer terminals. Ag5300 and Ag5324 modules are also well suited to applications in sectors such as IoT, Building Automation and Industrial Control requiring 12V or 24V with the ability to operate over the industrial temperature range from -40 to +85C.
Read more
- SIL - 57mm(L)x18mm(W)x14mm(H)
- 12V & 24V output options
- Adjustable output voltage
- Input voltage range 37V to 57V
- Overload, thermal and short-circuit protection
The Ag53000 series Power-over-Ethernet (PoE+) Powered Device (PD) modules are designed to extract power from a conventional twisted pair Category 5 Ethernet cable, conforming to the IEEE802.3 PoE standard, with full compatibility with the IEEE802.3at and IEEE802.3af amendments.
The Ag53000 is pre-configured as a Type 2 Class 4 PD device, requesting 30W of power from the PSE, with nominal output voltages of 12V or 24V.
The high efficiency DC/DC converter can achieve greater than 90% efficiency and operates over a wide input voltage range with a low ripple and low noise output. The DC/DC converter also has built-in output overload, output short-circuit and overtemperature protection and provides a 1500Vdc (input to output) isolation barrier.
The Ag53000 product series are pin for pin compatible with the popular Ag5300 and Ag5400 series – are lower cost – and are 100% Designed and Manufactured in the UK.
Read more
- 24W, Class 4 PD, 30W peak output power
- IEEE802.3at, IEEE802.3af compliant
- 90% efficient DC/DC converter
- 12V and 24V output variants available
- Low output ripple & noise
The Ag5400 is now the Highest Efficiency IEEE 802.3at Module in the world.
The Ag5400 series Power-over-Ethernet (PoE+) modules are designed to extract power from a conventional twisted pair Category 5 Ethernet cable, conforming to the IEEE802.3 PoE standard, with full backwards compatibility with the IEEE802.3bt, IEEE802.3at and IEEE802.3af amendments.
The Ag5400 is pre-configured as a Type 2 Class 4 device, allowing the module to draw up to 30W of power from the PSE.
The high efficiency DC/DC converter can achieve in excess of 93% efficiency and operates over a wide input voltage range with a low ripple and low noise output. The DC/DC converter also has built-in output overload, output short-circuit and overtemperature protection and provides a 1500Vdc (input to output) isolation barrier.
Read more
- Very high efficiency (>93%)
- Environmentally friendly
- SIL - 57mm(L)x18mm(W)x14mm(H)
- Very low heat output
- Low output ripple & noise
Visit Ecommerce Distributors
Recently viewed
The Ag59FE module is a Power-over-Ethernet Powered Device (PD) Controller module, which can be paired with a DC/DC converter to provide a complete PoE solution.
Designed to extract power from a conventional twisted pair Category 5 Ethernet cable, conforming to the IEEE802.3 PoE standard, with full compatibility with the IEEE802.3af, IEEE802.3at and IEEE802.3bt amendments.
The Ag59FE can be configured as a Type 1, 2, 3 or 4, Class 0-8 PD device, requesting up to 90W of power from the PSE.
When used in conjunction with an isolated DC/DC converter, constant current circuit, or enclosure, the application is capable of being configured as a fully compliant PD solution providing a DC voltage to the connected peripheral device.
Typical applications include, Power daisy chaining, PoE lighting, Ethernet extenders and media converters.
Read more
- Configurable Power Classification, from Class 0 to Class 8
- IEEE802.bt, IEEE802.3at, & IEEE802.3af compliant
- ‘Power Good’ Output
- Line Power Pass-through Output
- PoE Disable function
Designed for use in challenging environments, the Silver Telecom ST003 is a single Subscriber Line Interface Circuit (SLIC) in a 21 pin Dual-in-Line (DIL) format. The combination of features and packaging offers extremely efficient use of board area, saving significant system size and cost, minimising time to market for Telephony Systems developers.
The ST003 has been designed to work with loop lengths of typically 3.0km. Its performance to regulatory standards (G712) allows use in public and private network applications. With operation over an extended temperature range of -55C to +85C, ST003 is suitable for use in Industrial and Military Telecoms applications.
The ST003 has integral DC/DC converter and ringing generation thus providing all the line powering requirements from a single supply. The SLIC requires minimal external components.
The system interface has been designed for direct connection to popular codecs, for both audio and signalling.
The ST003 is ideal for low line count, short loop length applications, such as ISDN Terminal Adaptors, Internet Telephony (VoIP), Computer Telephony Integration (CTI), Wireless Local Loops (WLL) and Small Office Home Office (SOHO).
Read more
- wide temperature range -55C to +85C
- 600R impedance
- Very small DIL package
- Very Simple integration
- On-board ringing generator
